Shutters That Fit the Actual Opening, Not the Catalog Spec

Shutters installation in Bossier City for older homes where the mounting surface and window frame must both be verified before hardware is selected

Brick ranch homes built across the Shreveport-Bossier area in the 1950s through 1970s present a specific fitting challenge for shutters: the exterior brick surface and the window frame opening are two separate mounting conditions that often don't align with what catalog dimensions assume. The Blind Place Shreveport installs shutters using its own crew, and the installer who checks your mounting surface and measures your windows is the same person who returns to hang the shutters and test the louvers. No outside contractors are brought in at any point in that process.


On older brick ranch properties, the mortar joints, brick relief, and window trim depth each affect which hardware will seat flush and hold the shutter panel plumb. An installer who has only a measurement written on paper—rather than direct knowledge of the surface condition—may arrive with hardware that doesn't suit the wall material present. Checking the mounting surface is treated as part of the measuring visit, not a separate step, so the hardware selected matches what is actually there before anything is ordered.


Schedule an in-home visit to have your window openings and mounting surfaces assessed before shutter panels are specified or ordered.

What Proper Shutter Installation Requires

The installation sequence begins with a crew visit to measure each opening and evaluate the wall or trim surface where brackets will be anchored. On brick exteriors, that typically means selecting masonry anchors sized to the brick face rather than toggle hardware intended for drywall or wood trim. On siding or painted wood trim, the fastener type changes accordingly. Louver frames must be shimmed plumb if the opening itself is not perfectly square—a condition common in homes with settled foundations or decades of seasonal wood movement in the framing.


Once panels are hung, each louver is tested through its full tilt range and the hinges are checked for smooth swing without binding at the top or bottom corner of the frame. After the job is complete, you'll notice that the panels sit flat against the opening without a gap at any edge, the louvers move with consistent resistance across the full width, and the hinges don't allow the panel to sag away from the frame when open.


Shutter installation does not include painting or staining panels after mounting—if finish work is needed on painted wood shutters, that is done before the crew arrives to hang them. The installation scope covers measurement, hardware selection, panel hanging, shimming for plumb, and louver and hinge adjustment before sign-off.

What Property Owners Ask About Shutter Installation

The questions below address the installation process, how surface conditions affect the work, and what a correctly installed shutter should look like and feel like in operation.

  • How does the type of exterior wall material change how shutters are mounted?

    Brick requires masonry anchors driven into the mortar joint or brick face, while wood trim and fiber cement siding accept wood screws into solid backing; selecting hardware suited to the actual surface is the step that determines whether the bracket stays fixed under daily use.

  • What does it mean to shim a shutter panel plumb, and when is it necessary?

    Shimming involves placing thin material behind the hinge plate to bring the panel face into vertical alignment when the opening itself is not perfectly square; in older Bossier City homes where wall framing has settled over decades, this step is more common than it is in new construction.

  • How do you test shutter operation before the installation is considered finished?

    The louvers are tilted from fully open to fully closed and back, each hinge is checked for smooth swing without binding at the frame corners, and the panel is opened to confirm it holds its position rather than drifting shut under its own weight.

  • What affects whether a shutter is measured for an inside or outside frame position?

    Frame depth, the presence of window trim that would be covered, and the wall surface condition are each evaluated during the measuring visit—on older brick ranch homes, the exterior trim profile often determines mounting position before panel size is confirmed.

  • Why does the same person measuring and installing matter for a shutter job?

    The installer who checked the mounting surface knows which anchors were selected and why; if a condition discovered during the site visit required a change to the specified hardware, that information travels with the crew rather than being lost between a separate measuring appointment and a third-party installer.

The Blind Place Shreveport also installs shutters in Blanchard, Haughton, Vivian, Minden, and Shreveport. To begin, contact The Blind Place Shreveport to arrange a measuring visit where window dimensions and mounting surface conditions are assessed together.